The Cellpro 10XP PC Charge Control Software (CCS) installs from the FMA website using one of the following methods.

Please note, for best results, the Charge Control Software requires Microsoft Windows 2000 or higher. The FMA software requires Microsoft .NET 2.0 in order to install, launch and run semi-automatic updates. If you run Windows Vista x64 bit, you will be required to upgrade your existing Microsoft .NET 3.0 software install (included with Windows Vista) to Microsoft .NET 3.5 SP1. If you have recently performed an O.S. upgrade to Win7 (not a fresh install), you may need to re-install .NET 3.5 SP1 due to a confirmed bug in the update process which may cause problems when using .NET click once applications. Re-installing .NET 3.5 SP1 from the following MS web page will solve the problem. You may install this required update through Windows Update utility or by going to the Microsoft Download Center.

IMPORTANT: If you use a dial up connection and you use a dial up accelerator, disable it before proceeding. After installation, you may also need to disable it any time you launch the Cellpro 10XP Charge Control Software in order to receive updates without problems.

Method
1

–––––––––––––––––––––––––––––––––––––––––––
This is the preferred method of installation. This procedure requires that you have Internet Explorer 6.0 or higher and that it is set up as your default web browser for Windows.

If Internet Explorer is your default web browser, proceed to step 8 below. Otherwise, complete the following steps first:


1. Start > Control Panel

2. In the Control Panel, double-click Add or Remove Programs

3. In the Add or Remove Programs dialog, click Set Program Access and Defaults in the left panel

4. Open the Custom panel (if required)

5. Under Choose a default Web browser, click Internet Explorer

6. Click OK

7. Close the Add or Remove Programs dialog and the Control Panel dialog

* After installing the Charge Control Software, you can revert back to your preferred browse
r
.

8
. To install the FMA software using Internet Explorer 6.0 or higher set to your default browser, click:

Install Cellpro 10XP Charge Control Software


The above link to the install program will first check your computer for .NET 2.0 (or higher). If it is not already present, it will automatically install .NET 2.0 from the Microsoft website. After .NET is installed, the FMA software will install and launch.

9. Once the Charge Control Software launches, do not connect the PC interface to the PC's USB port or to the charger yet. Click on the link in the bottom left corner of the main program window titled "Download USB Driver". Follow the on-screen instructions to install the correct driver for your Windows operating system. Now connect the USB end of the cable to your computer's USB port, but do not yet connect the cable to the charger. Windows should automatically detect the FUIM2/FUIM3 interface and load the driver. Now connect the PC interface to the charger. With the Comm port set to "Auto", after less than 1 minute, the text "Waiting to Start" should appear at the top of the CCS program window. If the message indicates "No Data from Charger", check your connections and make sure the charger has power applied. If you still have problems, repeat the same procedure from the top. For more help, visit the product's FAQ section or contact technical support.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Method 2
––––––––––––––––––––––––––––––––––––––––––––
If you are using Mozilla Firefox as your default browser and you can not or do not want to change to IE 6.0 or higher, then follow these steps:


1. Install Microsoft .NET 2.0 by clicking the following link:


Install Microsoft .NET 2.0


2. Install the Mozilla Firefox .NET 2.0 plug-in by clicking the following link:

Install Mozilla Firefox .NET 2.0 plug-in

3. Install the FMA software using the following link:

Install Cellpro 10XP Charge Control Software


* Select “Run Click Once Application” when prompted by Firefox

If the install files used by Firefox remain on your computer after installation, you may remove them once installation has completed successfully. The following files may be found on your desktop and can safely be removed after installation:

dotnetfx.exe
setup.exe


4. Once the Charge Control Software launches, do not connect the PC interface to the PC's USB port or to the charger yet. Click on the link in the bottom left corner of the main program window titled "Download USB Driver". Follow the on-screen instructions to install the correct driver for your Windows operating system. Now connect the USB end of the cable to your computer's USB port, but do not yet connect the cable to the charger. Windows should automatically detect the FUIM2/FUIM3 interface and load the driver. Now connect the PC interface to the charger. With the Comm port set to "Auto", after less than 1 minute, the text "Waiting to Start" should appear at the top of the CCS program window. If the message indicates "No Data from Charger", check your connections and make sure the charger has power applied. If you still have problems, repeat the same procedure from the top. For more help, visit the product's FAQ section or contact technical support.

Please wait...